Pelco CM9760-CXTA Manuale Utente

CM9760-CXTACoaxitron® TranslatorInstallation/Operation ManualC539M-A (12/01)®Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • www.pelco.comIn Nort

10 Pelco Manual C539M-A (12/01)2.1.4.2 Protocol TypeThis bit is set to correspond to the protocol input of the associated controller (see Figure 7).F

Pelco Manual C539M-A (12/01) 112.1.4.5 Channel or Address SelectIf DIP 1-7 is set to the OFF position, the translator responds to addresses 1-16. If

12 Pelco Manual C539M-A (12/01)SECTION III: CXTA INSTALLATION3.1 MOUNTING THE CXTAInstallation of the CM9760-CXTA translator is relatively simple (r

Pelco Manual C539M-A (12/01) 133.2.2 9760 SYSTEM HOOKUP (P Protocol)Two possibilities are:1. Single or multiple translators hooked to unique Sercom p

14 Pelco Manual C539M-A (12/01)Flowchart 1. Installation Decision TreeThe following flowchart might prove helpful as an aide in configuring the diffe

Pelco Manual C539M-A (12/01) 15Figure 13. Direct Mode Installation

16 Pelco Manual C539M-A (12/01)Figure 14. 9760 System Installation

Pelco Manual C539M-A (12/01) 17Figure 15. DX7000 Installation

18 Pelco Manual C539M-A (12/01)Figure 16. MPT9500 Installation

Pelco Manual C539M-A (12/01) 193.3 SOFTWARE CONSIDERATIONSDespite the considerations given in this section to highlight aspects of required softwarese

2 Pelco Manual C539M-A (12/01)CONTENTSSECTION I: CXTA OVERVIEW1.1 DESCRIPTION ...

20 Pelco Manual C539M-A (12/01)3.3.2 CM9760-KBD DIRECT MODEConsult the required manuals for setting up direct mode operation. The KBD manual(C540M) i

Pelco Manual C539M-A (12/01) 21SECTION IV: CXTA OPERATION4.1 POWER-UPAt power up, the system microcontroller reads the configuration switch, dip swi

22 Pelco Manual C539M-A (12/01)SECTION V: APPENDIX5.1 COMMUNICATION PARAMETERSThere is only one basic set of signal interface rules that you must con

Pelco Manual C539M-A (12/01) 23If a cable is “straight”, then pin 1 at one end of the cable goes to pin 1 at the opposite endof the cable. If the conn

24 Pelco Manual C539M-A (12/01)5.2 CABLE PARAMETERSData communication cables are used in the CM9760 system to connect required equipment toappropriate

Pelco Manual C539M-A (12/01) 25Most of the time, connection cables are supplied with the device. As long as the suppliedcable is appropriate, no probl

26 Pelco Manual C539M-A (12/01)Although the communication link can be as far away as 4,000 feet (1,220 m) (per Figure 20),this is theoretical. Pelco r

Pelco Manual C539M-A (12/01) 27SECTION VI: GENERAL6.1 SPECIFICATIONSELECTRICALInput Voltage: 100-240 VAC, 50/60 Hz, auto-rangingPowerConsumption: 15VA

28 Pelco Manual C539M-A (12/01)REVISION HISTORYManual # Date CommentsC539M 1/98 Original version. 8/01 Baud reference correction.C539M-A 12/01 C

Pelco Manual C539M-A (12/01) 3LIST OF TABLESTable PageA Connection Disparities ...

4 Pelco Manual C539M-A (12/01)(This page intentionally left blank.)

Pelco Manual C539M-A (12/01) 5IMPORTANT SAFEGUARDS AND WARNINGSPrior to installation and use of this product, the following WARNINGS should be observe

6 Pelco Manual C539M-A (12/01)NOTE: For those familiar with device attachment to 9760 systems, a convenientreference box is provided in the margin th

Pelco Manual C539M-A (12/01) 7SECTION II: CXTA DEFINING CHARACTERISTICSA number of configuration and connection decisions are made at the CXTA level

8 Pelco Manual C539M-A (12/01)The breakdown, with respect to cascading for each controller, is as follows:• For the 9760, cascading is allowed; addres

Pelco Manual C539M-A (12/01) 92.1.4 CONFIGURATION SWITCHThe decode of configuration switch functions is indicated in Figure 5 and discussed in detail